Metal connectors, fasteners and anchors can corrode and lose carrying capacity when installed in corrosive environments or when installed in contact with corrosive materials. The many variables present in a building environment make it impossible to predict accurately whether, or when, corrosion will begin to reach a critical level. This relative uncertainty makes it crucial that specifiers and users be knowledgeable about the potential risks and select a product suitable for the intended use. When there is any uncertainty about the possible corrosion risks of any installation, a qualified professional should be consulted. Because of the risks posed by corrosion, periodic inspections should be performed by a qualified engineer or qualified inspector and maintenance performed accordingly.
It’s common to see some corrosion in outdoor applications. Even stainless steel can corrode. The presence of some corrosion does not mean that load capacity has been affected or that failure is imminent. If significant corrosion is apparent or suspected, then the wood, fasteners, anchors, and connectors should be inspected by a qualified engineer or qualified inspector. Replacement of affected components may be appropriate.
Because of the many variables involved, bob体育欧洲杯哪里可以买球 cannot provide estimates of the service life of connectors, anchors, and fasteners. We suggest that all users and specifiers obtain recommendations on corrosion from the suppliers of the materials that will be used with bob体育欧洲杯哪里可以买球 products, in particular, treated wood or concrete. We have attempted to provide basic knowledge on the subject here, and have additional information in our technical bulletins on the topic (Product Use Information).
Corrosion can result from many combinations of environmental conditions, materials, construction design, and other factors, and no single guideline addresses all corrosion possibilities. Nevertheless, important corrosion information can be obtained from the American Wood Protection Association (AWPA), the International Building Code (IBC), International Residential Code (IRC), and local building codes. The following discussion provides general guidelines and approaches for the selection of bob体育欧洲杯哪里可以买球 products for various construction conditions, but is not intended to supersede the guidelines of the AWPA, IBC, IRC, or local building codes.
Corrosion issues for bob体育欧洲杯哪里可以买球 products generally fall into five categories:
Many environments and materials can cause corrosion, including ocean salt air, condensation, duration of wetness, fire retardants, fumes, fertilizers, chlorides, sulfates, preservative-treated wood, de-icing salts, dissimilar metals, soils, and more. Designers must take all of these factors into account when deciding which bob体育欧洲杯哪里可以买球 products to use with which corrosion-resistant coatings or materials.
The design, quality of construction, and misinstallation can directly affect the corrosion resistance of products. A product intended and installed for use in dry-service environment may corrode if the structure design or building materials allow moisture intrusion, or expose the product to corrosive conditions, such as moisture or chemicals contained in the construction materials, soils, or atmospheres.
Some wood-preservative or fire-retardant chemicals or chemical retention levels create increased risk of corrosion and are corrosive to steel connectors and fasteners. For example, testing by bob体育欧洲杯哪里可以买球 has shown that ACQ-Type D is more corrosive than Copper Azole, Micronized Copper Azole, or CCA-C. At the same time, other tests have shown that inorganic boron treatment chemicals, specifically SBX-DOT, are less corrosive than CCA-C.
Because different chemical treatments of wood have different corrosion effects, it’s important to understand the relationship between the wood treatment chemicals and the coatings and base metals of bob体育欧洲杯哪里可以买球 products.
The preservative-treated wood supplier should provide all of the pertinent information about the treated wood product. The information should include the AWPA Use Category Designation, wood species group, wood treatment chemical, and chemical retention. See building code requirements and appropriate evaluation reports for corrosion effects of wood treatment chemicals and for fastener corrosion resistance recommendations.
With Fire-Retardant (FRT) Wood, the 2015 and 2018 IBC Section 2304.10.5, 2021 IBC Section 2304.10.6, and 2015, 2018 and 2021 IRC Section R317.3.4 refer to the manufacturers for fastener corrosion reqirements. In the absence of recommendations from the FRT manufacturer, the building codes require fasteners to be hot-dip galvanized, stainless steel, silicon bronze or copper. bob体育欧洲杯哪里可以买球 further requires that the fastener is compatible with the metal connector hardware. Fastener shear and withdrawal allowable loads may be reduced in FRT lumber. Refer to the FRT manufacturer’s evaluation report for potential reduction factors..
Galvanic corrosion occurs when two electrochemically dissimilar metals contact each other in the presence of an electrolyte (such as water) that acts as a conductive path for metal ions to move from the more anodic to the more cathodic metal. Good detailing practice, including the following, can help reduce the possibility of galvanic corrosion of fasteners and connectors:
If you are uncertain about the galvanic corrosion potential of any installation, always consult with a corrosion expert. See the product pages for particular parts for more information regarding what coating systems are recommended or required for use with the parts in question.
Some hardened fasteners may experience premature failure from hydrogen-assisted stress-corrosion cracking if exposed to moisture. These fasteners are recommended for use only in dry-service conditions.
Indoor swimming pool environments are extremely corrosive to steel products. And some stainless steel is highly susceptible to stress corrosion cracking (SCC) under sustained loads in this environment. SCC can result in sudden failures. Instead of stainless steel, it is advised to use a duplex coated, post-hot-dip galvanized or ZMAX® coated low carbon steel for any load bearing components used in swimming pool environments. Regular maintenance is strongly advised.
bob体育欧洲杯哪里可以买球 connectors, anchors and fasteners feature a wide range of materials and coatings designed to meet specific performance criteria. It is important to select a material and/or coating that is suitable for the intended application and environment based upon factors such as corrosion resistance and mechanical properties of the material. For more information on selecting connectors, anchors and fasteners based upon corrosion resistance, please seeCorrosion Information for Connectors and Fasteners, andCorrosion Information for Anchoring bob综合官网登录.
If the treatment chemical information is incomplete, bob体育欧洲杯哪里可以买球 recommends the use of a 300 series stainless steel product. Also if the treatment chemical is not shown in the Corrosion Classification Table, then bob体育欧洲杯哪里可以买球 has not evaluated it and cannot make any recommendations other than the use of coatings and materials in the Severe category. Manufacturers may independently provide test results of other product information; bob体育欧洲杯哪里可以买球 expresses no opinion regarding such information.
|Minimum Corrosion Resistance Recommendations|
|FASTENERS & ANCHORS|
|Phosphate (gray, black),
Clear (bright) zinc (ASTM F1941),
Heavy electro-galvanized (ASTM A641-Class 1),
Yellow zinc (ASTM F1941),
Type 410 stainless steel
|Mechanically galvanized (AS 3566.2-C3, N2000, ASTM B695-Class 55),
Quik Guard® coating,
Hot-dip galvanized (ASTM A153-Class D),
Type 410 stainless steel with protective top coat
|Type 304 stainless steel,
Type 305 stainless steel
|Type 316 stainless steel,
Hot-dip galvanized (ASTM A153-Class C),
Silicon bronze, Copper
|bob体育欧洲杯哪里可以买球 gray paint,
Standard G90 zinc coating
Hot-dip galvanized (ASTM A123)
|Type 316L stainless steel||Type 316L stainless steel|
|Corrosion Resistance Classifications|
|Environment||Material to be Fastened|
|Untreated Wood or Other Material||Preservative-treated Wood||FRT Wood|
|SBX-DOT Zinc Borate||Chemical Retention ≤ AWPA, UC4A||Chemical Retention > AWPA, UC4A||ACZA||Other or Uncertain|